News

Jun 19, 2023

Bismuth sulfoiodide (BiSI) nanorods: synthesis, characterization, and photodetector application

Scientific Reports volume 13, Article number: 8800 (2023) Cite this article 1614 Accesses Metrics details The nanorods of bismuth sulfoiodide (BiSI) were synthesized at relatively low temperature (393

Scientific Reports volume 13, Article number: 8800 (2023) Cite this article

1614 Accesses

Metrics details

The nanorods of bismuth sulfoiodide (BiSI) were synthesized at relatively low temperature (393 K) through a wet chemical method. The crystalline one-dimensional (1D) structure of the BiSI nanorods was confirmed using high resolution transmission microscopy (HRTEM). The morphology and chemical composition of the material were examined by applying scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS), respectively. The average diameter of 126(3) nm and length of 1.9(1) µm of the BiSI nanorods were determined. X-ray diffraction (XRD) revealed that prepared material consists of a major orthorhombic BiSI phase (87%) and a minor amount of hexagonal Bi13S18I2 phase (13%) with no presence of other residual phases. The direct energy band gap of 1.67(1) eV was determined for BiSI film using diffuse reflectance spectroscopy (DRS). Two types of photodetectors were constructed from BiSI nanorods. The first one was traditional photoconductive device based on BiSI film on stiff glass substrate equipped with Au electrodes. An influence of light intensity on photocurrent response to monochromatic light (λ = 488 nm) illumination was studied at a constant bias voltage. The novel flexible photo-chargeable device was the second type of prepared photodetectors. It consisted of BiSI film and gel electrolyte layer sandwiched between polyethylene terephthalate (PET) substrates coated with indium tin oxide (ITO) electrodes. The flexible self-powered BiSI photodetector exhibited open-circuit photovoltage of 68 mV and short-circuit photocurrent density of 0.11 nA/cm2 under light illumination with intensity of 0.127 W/cm2. These results confirmed high potential of BiSI nanorods for use in self-powered photodetectors and photo-chargeable capacitors.

Bismuth sulfoiodide (BiSI) is a ternary semiconductor that belongs to the chalcohalide family of inorganic materials1,2. The crystal structure of the BiSI is described by the orthorhombic Pnam space group3,4. This material grows into the needle-shaped bulk crystals5,6,7, one-dimensional (1D) microrods8,9, nanorods10,11,12,13,14, and nanowires15. The BiSI crystals consist of the [(BiSI)∞]2 double chains bonded together by the weak van der Waals interactions1,16. The chains are oriented along the c-axis, i.e. [001] direction5,13,17. Therefore, this material possesses highly anisotropic optical and electrical properties. The BiSI is n-type semiconductor8,9,18,19 with energy band gap reported in the wide range from 1.5 eV20 up to 1.8 eV15,21,22. BiSI is considered as an efficient solar absorber for photovoltaic devices8,21. It has been demonstrated as an excellent photoconductor with large photoconductive gain17,23. Moreover, it exhibits small effective mass of electrons and holes which is beneficial for its use in room temperature radiation detectors1,24. The BiSI is also a ferroelectric material25,26,27. Recently, an intrinsic ultra-low lattice thermal conductivity of orthorhombic BiSI has been revealed suggesting that this compound is promising for thermoelectric applications28. Until now, the BiSI has been reported as an excellent material for use in high performance photodetectors17, solar cells2,9,11,13,20,29,30, photoelectrochemical cells8,19,31, supercapacitors3,4,32,33, rechargeable batteries16, room temperature ionizing radiation detectors10,12, photocatalytic degradation of organic pollutants15,34,35, and hydrogen production36.

The BiSI can be fabricated using different approaches, including solid-state mechanochemical method37,38, hydrothermal growth22,34,35,39, solvothermal synthesis10,12,14,18, solution precipitation method32, colloidal approach19, thermolysis20, vapor phase growth5,6, and sulfurization of the bismuth oxyiodide (BiOI) in presence of diluted H2S gas via anion exchange of the oxygen with sulfur17,31. Usually, a synthesis of BiSI nanorods is accompanied with formation of minor phase of rod-like Bi13S18I218 or sheet-like BiOI32, depending on applied fabrication method. Li and coworkers18 demonstrated that the BiSI can be synthesized under low sulfur to bismuth ratio. When this parameter is increased significantly, the BiSI is converted into the Bi13S18I2. Many of the aforementioned fabrication methods result in formation of textured thin films with random crystal orientation40. The one-dimensional BiSI microstructures grow in the natural environment, too. The BiSI is known also as demicheleite-(I) mineral. In 2010, it was discovered in La Fossa crater on the Vulcano Island (Italy)41.

Recently, Zankat et al.42 have developed self-powered photodetector based on SnSe2/MoSe2 heterostructure. An influence of MoSe2 crystal anisotropy on self-powered photodetection of SnSe2/MoSe2 heterojunction was investigated. The device exhibited type-II junction with high photoresponsivity of 7.09 A/W, detectivity of 6.44 × 1012 Jones, and ON/OFF ratio of 105–10642. Patel et al.43 illustrated the ability to use p-WSe2/p-CuO heterostructure to make a flexible, robust, and broadband photodetector at a low cost. The WSe2/CuO thin film was deposited on the paper substrate using a non-toxic, solvent-free, and environmentally friendly handprint process. This paper-based photodetector showed an effective optoelectrical performance over extended spectral range of 390–800 nm with a considerable responsivity of 0.28 mA/W and specific detectivity of 0.19 × 1010 Jones43. The sonication assisted mechanical mixing and drop-casting technique were presented in44 and used to construct a hybrid junction of selenium and poly (3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS). This heterojunction was applied as a high-performance photodetector. It demonstrated a broad spectrum response in the UV–Vis-NIR region with responsivity of 0.56 A/W, 66 mA/W, and 1.363 A/W at wavelength of 315 nm, 620 nm, and 820 nm, respectively44. Chekke et al.45 fabricated self-powered flexible and wearable single-electrode triboelectric nanogenerator device using Au nanoparticle decorated WS2 nanosheets, cellulose paper, and polyvinyl alcohol (PVA) membrane substrate. It exhibited a photo-detection property with a sensitivity of 0.4 Vm2/W. Vuong et al.46 showed that chemical-vapor-deposited methylammonium bismuth iodide [MA3Bi2I9 (MBI)] films and their mixed halide analogues [MA3Bi2I6Br3 (MBIB), MA3Bi2I6Cl3 (MBIC)] improve the performance and stability of photodetectors. When MBIC-integrated devices were illuminated with UV light, they showed responsivity of 0.92 A/W and detectivity of 2.9 × 1013 Jones, which were approximately three times greater than MBI counterparts46. Patel and co-workers demonstrated the fabrication of a flexible film of Ag nanoparticle decorated WSe2 on a paper substrate47. This material was utilized in a photodetector which responsivity and detectivity at a low bias of 1 V attained 0.43 mA/W and 2.9 × 108 Jones, respectively47. Pataniya et al.48 developed a dip-coated WSe2 photodetector on Whatman filter paper as the substrate. Its responsivity reached 17.78 mA/W under 5 V bias voltage, which was equivalent to previous two-dimensional transition metal dichalcogenides photodetectors on rigid substrates. In another work, Modi et al.49 employed straightforward hydrothermal method to synthesize indium-doped SnS ternary alloys. The best photodetector performance was achieved for 7% In doped SnS. The large responsivity of 85 A/W and detectivity of 8.96 × 1010 Jones were determined for this photodetector at 1 V bias voltage under illumination intensity of 6.96 mW/m249.

In this paper, a facile wet chemical fabrication method of BiSI nanorods is presented. It allowed to obtain high purity material at relatively low temperature (393 K) without a need of application of complex and expensive equipment. The comprehensive studies of morphology, chemical composition, crystal structure, and optical properties of the BiSI nanorods were performed using different experimental techniques, such as high resolution transmission microscopy (HRTEM), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and diffuse reflectance spectroscopy (DRS). The BiSI nanorods were used to construct two types of photodetectors. The first one was traditional photoconductive device which consisted of the BiSI film on stiff glass substrate. The second one was the flexible photo-chargeable photodetector based on the BiSI and gel electrolyte films clamped in between ITO coated PET layers. The response of the photodetectors to monochromatic light (λ = 488 nm, 632.8 nm) illumination was measured. An influence of light intensity on photocurrent response was investigated. The parameters describing photodetectors performance were determined and discussed.

A typical process of the material fabrication is depicted in Fig. 1. In the first step, 0.485 g of bismuth nitrate pentahydrate (Bi(NO3)3·5H2O) was dissolved in 50 mL of deionized (DI) water and heated to 393 K (Fig. 1a). Then, 0.34 g of potassium iodide (KI) and 1.0 g of thioacetamide (TAA) were dissolved in 50 mL of DI water and heated to 393 K (Fig. 1b). The Bi(NO3)3·5H2O solution was slowly added to the mixture of KI and TAA (Fig. 1c). The pH value of the solution was adjusted to 1–1.2 by adding an appropriate amount of acetic acid (AcOH). The reaction was continued for next 5 h at 393 K under continuous stirring condition (Fig. 1d). After completion of the reaction, the precipitate was washed and centrifuged several times with ethanol (4 times) and deionized water (6 times) until the supernatant liquid became colorless. Later, the precipitate was dried at 333 K for 8 h (Fig. 1e). Finally, the black powder containing one-dimensional BiSI nanorods was obtained (Fig. 1f).

Schematic diagram of the material synthesis: (a) bismuth nitrate dissolved in deionized water, (b) potassium iodide and thioacetamide dissolved in deionized water, (c) the bismuth nitrate solution added to potassium iodide and thioacetamide mixture, (d) the solution stirring along with pH adjusting by adding the acetic acid, (e) material drying, and (f) SEM micrograph of the prepared material. Detailed description is provided in the text.

The morphological analysis and elemental mapping of the BiSI nanorods were accomplished using bright field imaging in JEM-2100F TEM microscope (JEOL). The acceleration voltage was adjusted to 200 kV. Further characterization of the morphology and chemical composition of the prepared material was carried out with a Phenom Pro X (Thermo Fisher Scientific) SEM microscope integrated with EDS spectrometer. The SEM microscope was operated at an acceleration voltage of 15 kV. The EDS spectrum was quantified using a ProSuite Element Identification (Thermo Fisher Scientific) software.

XRD studies were performed using the D8 Advance diffractometer (Bruker) with Cu-Kα cathode (λ = 1.54 Å) operating at 40 kV voltage and 40 mA current. The scanning step of 0.02° with a scan rate of 0.40°/min in the angle (2Θ) range from 10° to 120° was used. The DIFFRAC.EVA program and International Centre for Diffraction Data (ICDD) PDF#2 database were applied to identify the phases in the XRD spectrum. The exact lattice parameters and crystallite size of fitted phases were calculated using Rietveld refinement in TOPAS 6 program, basing on Williamson-Hall theory50,51. The pseudo-Voigt function was applied for a description of diffraction line profiles at the Rietveld refinement. The weighted-pattern factor (Rwp), expected R factor (Rexp) and goodness-of-fit (GOF) parameters were used as numerical criteria of the quality of the fit of calculated to experimental diffraction data52. Peak shapes, lattice parameters, crystallite size and lattice strain were refined simultaneously50,51,53.

DRS spectrum of the BiSI nanorods was recorded at room temperature using PC-2000 spectrophotometer (Ocean Optics Inc.) connected to the ISP-REF integrating sphere (Ocean Optics Inc.). The sample for optical measurements was prepared as follows. A small amount of material was added to ethanol and agitated ultrasonically for 30 min. Then, the suspension of BiSI nanorods in ethanol was drop casted on a glass substrate multiple times. The material deposition was continued until the glass substrate was fully coated with BiSI. After that, the sample was dried at room temperature to evaporate the ethanol.

Two types of photodetectors were constructed. The first one was fabricated as follows. The BiSI nanorods were dispersed in ethanol and agitated ultrasonically for 1 h. Afterwards, the BiSI suspension in ethanol was drop casted onto the glass plate and dried. This process was repeated multiple times until the glass plate was fully coated with BiSI. The gold electrodes with a distance of 385 µm were sputtered on the BiSI film using Q150R ES rotary pumped coater (Quorum Technologies Ltd.). The gold layers were chosen as the materials for the photodetector electrodes due to their high quality and chemical stability54. Thin metal wires were attached to the sample electrodes with a high purity silver paste. The second type of photodetectors was prepared according to the procedure described below. The BiSI nanorods (200 mg) were dispersed in ethanol (12 mL) and agitated ultrasonically. The suspension of BiSI nanorods in ethanol was drop casted onto polyethylene terephthalate (PET) substrate coated with indium tin oxide (ITO) layer. Then, the sample was dried. The drop casting was repeated for 20 times to achieve a dense BiSI layer on the ITO electrode. In the next step, the sample was heated at temperature of 333 K for 1 h in order to evaporate the residual ethanol. The potassium hydroxide (KOH) (1 g) was dissolved in deionized water (6 mL) and stirred for 1 h at 333 K. The poly(vinyl alcohol) (PVA) (1.5 g) was dissolved in deionized water (10 mL) and stirred for 1 h at 353 K. The aqueous solutions of KOH and PVA were mixed together and heated at temperature of 353 K. A piece of filter paper (AeroPress) with average pore size of 20 µm was placed on the PET/ITO/BiSI sample. It served as a separator which was infiltrated with PVA-KOH solution. The ITO coated PET was attached to the top of the sample. In order to ensure a good connection between BiSI, PVA-KOH, and ITO layers, the sample was clamped into small clips. In order to obtain solidified gel electrolyte, the PET/ITO/BiSI/PVA-KOH/ITO/PET sample was subjected to elevated temperatures of 353 K and 323 K for 1.5 h and 12 h, respectively.

The fabricated samples were inserted into the H-242 environmental test chamber (Espec) and tested as photodetectors. The measurements of photoelectric properties of BiSI nanorods were accomplished at a constant temperature of 293 K and relative humidity (RH) of 50%. The photoelectric response of the BiSI nanorods was registered at a constant bias voltage using Keithley 6517B electrometer (Tektronix). In the case of the Au/BiSI/Au photodetector, the bias voltage of 50 V was applied. Such value of bias voltage (or even higher) was commonly used for other photodetectors55,56,57,58. Furthermore, an application of higher voltage results in achieving of larger photocurrent response of photodetector. It allows also to reduce noise and increase the precision of measurements. The data acquisition was carried out using a PC computer and LabView program (National Instruments). The BiSI based photodetector was illuminated with blue (λ = 488 nm) and red (λ = 632.8 nm) light emitted by argon laser Reliant 50 s (Laser Physics) and helium neon laser 25-LHP (Melles Griot), respectively. The radiation was transmitted from laser to the photodetector using the UV–VIS optical fiber. The neutral filters were applied to adjust the light intensity.

Figure 2 presents TEM images of the prepared material. The BiSI exhibited one-dimensional structure with lengths from a few hundreds of nanometers up to a several micrometers (Fig. 2a). The clear lattice fringes were observed in the HRTEM image of the nanorods tips (Fig. 2d). Determined interplanar distance d = 0.425(1) nm was equal within an experimental uncertainty to the distance of 0.4259 nm between (200) planes in the orthorhombic BiSI (PDF 00-043-0652). The same interplanar distance was observed in the HRTEM images of the BiSI nanorods prepared via solvothermal method13,18. The lattice fringes of 0.302(1) nm and 0.273(3) were identified as interplanar distances of 0.3027 nm and 0.2736 nm between (121) and (310) planes, respectively. It allowed to confirm that the nanorods, shown in Fig. 2, belong to the pure orthorhombic BiSI. The lattice fringes corresponding to the (121) crystallographic plane of BiSI were also reported in the case of BiSI nanorods fabricated from solution4,14 and through solvothermal method12. The elemental mapping of the nanorods bundle is presented in Fig. S1 in the “Supplementary data”. The expected elements (bismuth, sulfur, and iodine) were uniformly distributed in the BiSI nanorods. It suggested the formation of the pure BiSI phase.

TEM images of the BiSI nanorods (a-d) recorded at different magnifications. The figures (c,d) represent the magnified areas marked by the red dashed rectangles in figures (b,c), respectively. The lattice fringes of 0.425(1) nm, 0.302(1) nm, and 0.273(3) nm correspond to the interplanar distances between (200), (121), and (310) planes of the orthorhombic BiSI (diffraction card No. PDF 00-043-0652).

The prepared material was deposited on the silicon wafer and examined using SEM microscopy (Fig. 3). The material consisted of the crystalline rod-like or needle-like nanostructures with a random arrangement. The BiSI nanorods had tendency to be agglomerated into the bundles (Figs. 3a–c). However, the separate nanorods were observed, too. A typical individual BiSI nanorod with diameter of 73 nm and length of 1.09 µm is depicted in Fig. 3d. The observed growth of the material into bundled one-dimensional nanorods is in agreement with the BiSI crystal structure as reported in the literature. The BiSI possesses the form of a binary screw axis linked together by a strong Bi-S covalent bond, whereas the halogen anion has an ionic bond with a covalent binding bridge1. The [(BiSI)∞]2 double chains are connected by the weak van der Waals interactions and they are oriented along the c-axis13.

Typical SEM micrographs of the BiSI nanorods bundles (a–c) and an individual BiSI nanorod (d) deposited on Si substrate.

SEM and TEM images were analyzed in order to determine distribution, average values, and median values of the BiSI nanorods dimensions. The measurements of diameters and lengths were performed on 750 and 250 randomly selected nanorods, respectively. It was found that the distribution of the BiSI dimensions (Fig. 4) followed well a log–normal function59,60

where x denotes the nanorod dimension (diameter or length), xm is the median value of the nanorod dimension, σ means a standard deviation, A is a constant parameter. Usually, the log–normal function describes sizes distribution of nanorods14,61,62,63,64, nanowires65,66, as well as nanoparticles60,67,68. The diameters of the BiSI nanorods were observed in a broad range from about 15 nm up to 530 nm, whereas the majority of them varied between 50 and 100 nm (Fig. 4a). The average and median values of nanorods diameters were equal to da = 126(3) nm and dm = 99(2) nm, respectively. The lengths of BiSI nanorods were in the range from approximately 190 nm to 10.2 µm (Fig. 4b). The most of nanorods were longer than 1 µm and shorter than 2 µm. The average length of La = 1.9(1) µm and median length of Lm = 1.65(5) µm were determined.

Distribution of diameters (a) and lengths (b) of the BiSI nanorods. The black lines represent log-normal distribution as described by Eq. (1). The fitted parameters of Eq. (1) are provided in the text. The inset tables show determined average and median values of BiSI nanorods diameters and lengths.

Table 1 shows an overview of the sizes of BiSI one-dimensional nanostructures reported in the literature. The BiSI nanorods, presented in this paper, exhibited the diameter range similar to those prepared using solvothermal method10,12,13,14,36. However, the BiSI nanorods, described herein, were statistically shorter than other 1D BiSI nanostructures3,4,18,39. This difference might result from the various synthesis conditions. Both temperature69 and time70,71 of synthesis can influence the length of the nanorods. It should be underlined that hydrothermal and solvothermal methods require use of high temperature (typically 453 K10,12,14,36) and long reaction time (15–30 h3,4,10,12,14,15,39). In our approach, proposed in this work, the synthesis temperature and time are significantly reduced to 393 K and 5 h, respectively. Furthermore, this fabrication method is a facile and it does not involve use of complex or expensive equipment.

The EDS analysis confirmed that the material consisted of only bismuth (Bi), sulfur (S), and iodine (I) with an elemental atomic ratio of 0.45:0.21:0.34 for Bi, S and I, respectively. The EDS spectrum was corrected by removing the signal originating from silicone (Si) substrate. No other elements were detected indicting high purity of the material. A similar deficiency of sulfur was demonstrated by the X-ray photoelectron spectroscopy (XPS) of the BiSI thin films prepared from single precursor solution23 and sulfurization of the BiOI in diluted H2S gas17. A sulfur-deficient composition was also reported in the case of one-dimensional BiSI nanostructures which were fabricated using solvothermal method16. The EDS elemental mapping and line scan of the BiSI nanorods deposited on Si substrate are presented in the “Supplementary data” in Figs. S2 and S3, respectively. The distributions of bismuth, sulfur, and iodine were almost homogeneous over the sample surface and along the BiSI nanorods.

X-ray diffraction pattern of the fabricated material is presented in Fig. 5. It consisted of high sharp peaks indicating high crystallinity of the examined material. The orthorhombic BiSI was identified as the main phase. A presence of some residues was also detected. Two strong peaks at 23.8° and 28.1° as well as weak peaks at 17°, 26°, 32°, 45°, 51.6°, 52.5°, and 63° were identified as typical ones for the hexagonal Bi13S18I24,72. Quantitative analysis confirmed a major amount of BiSI phase (87%) and a minor amount of Bi13S18I2 phase (13%), with no presence of other residual phases. The results of Rietveld refinement are provided in Fig. S4 and Table S1 in the “Supplementary data”. A good fit of selected phases to the acquired pattern was obtained. The slight enlargement of the crystal lattice and high lattice strain were observed. These effects can be probably ascribed to the fabrication procedure of the material, resulting in minor misfit of atoms in crystal structure. It should be noted that the growth of the BiSI nanorods from solution is usually accompanied with formation of residual Bi13S18I24,18. Groom and co-workers72,73 demonstrated that the iodine concentration in the S/I2 flux and temperature of the reaction are crucial parameters that influence the exact amounts of BiSI and Bi13S18I2 in final product.

X-ray diffraction pattern of the prepared material. The XRD peaks were identified to BiSI (blue inverted triangle) and Bi13S18I2 (red circle) phases.

Diffuse reflectance spectrum of the BiSI nanorods is presented in Fig. 6a. It showed a clear absorption edge at photon wavelength of about 750 nm. The values of diffuse reflectance coefficient (Rd) were converted into the Kubelka–Munk function using well known equation

The diffuse reflectance spectrum (a) and Tauc plot (b) for the BiSI nanorods. An inset in figure (a) shows photograph of the BiSI nanorods film deposited on a glass plate. The red curve in figure (b) represents the best fitted dependence described by Eq. (3).

The Kubelka–Munk function is proportional to the absorption coefficient74. The band gap energy (Eg) of examined material was determined by applying Tauc’s formula18,32

where hν is incident photon energy, A and n are constants. The exponent n is equal to 1/2 or 2 in the case of the allowed direct or indirect transitions, respectively. The value of n was set to 1/2 since BiSI is regarded as a semiconductor with direct energy band gap8,17,20,23. The energy band gap of 1.67(1) eV was determined by extrapolating the straight line to zero absorption in the graph of transformed Kubelka–Munk function versus photon energy (Fig. 6b). The calculated value of Eg was compared with literature data for BiSI (Table 2). One can see that the energy band gap of BiSI is reported in broad range from 1.33 eV32 to 1.8 eV15,22,37. The value of energy band gap of BiSI may depend on many factors, including material morphology75, size of the micro/nanostructures76,77, and material thickness17. The determined Eg value allows to clearly identify the main phase of examined material as BiSI, since the indirect and direct band gaps of Bi13S18I2 at room temperature are much lower and they equal to 0.73 eV and 1.06 eV78, respectively.

The two types of photodetectors were investigated. The first one consisted of BiSI film deposited on the glass substrate (Fig. 7a). Figure 7b presents the current–voltage characteristics of this device measured in dark condition and under monochromatic light illumination. The BiSI photodetector was illuminated with blue (λ = 488 nm) and red (λ = 632.8 nm) light to demonstrate its suitability for a full visible spectrum detection. In both cases, the light intensity was the same (127 mW/cm2). An existence of the band bending at the Au/BiSI junction is expected. A photocurrent generation in the Au/BiSI/Au device and energy band diagrams in dark condition and under light illumination are presented in Fig. S5 in the “Supplementary data”. The transient characteristics of the photocurrent registered at a constant bias voltage under red (λ = 632.8 nm) and blue (λ = 488 nm) light illumination are shown in Fig. 7c, d, respectively. An influence of light intensity on transient characteristics of the photocurrent was examined (Fig. 7d). An increase of the light intensity resulted in obvious enhancement of the photocurrent. The response of the Au/BiSI/Au photodetector exhibited an excellent repeatability. A stability of the photocurrent response is an important feature of the photodetector79,80,81,82,83. It should be underlined that photocurrent response did not show any drift, what proved a good stability of the device operation (Fig. 7d). The dependence of light intensity on photocurrent (Fig. 7e) was best fitted with well-known power law equation84,85,86,87

where IPC0 is a constant, IL means light intensity, γ is the power exponent that depends on light wavelength. The coefficient γ = 0.49(2) was determined for λ = 488 nm. The value of γ < 1 suggested the photogating effect88 as a dominant mechanism of the photocurrent generation. It can be probably ascribed to the existence of the trapping states in the BiSI nanorods84.

(a) A scheme of the biased photodetector consisting of BiSI nanorods film on glass substrate with sputtered Au electrodes, (b) current–voltage characteristics of the Au/BiSI/Au photodetector measured in dark condition and under monochromatic light illumination (IL = 127 mW/cm2), (c) transient characteristics of photocurrent registered at a constant bias voltage (U = 50 V, T = 293 K, RH = 50%, λ = 632.8 nm, IL = 127 mW/cm2), (d) transient characteristics of photocurrent measured for different light intensities at a constant bias voltage (U = 50 V, T = 293 K, RH = 50%, λ = 488 nm, ILmax = 127 mW/cm2), (e) influence of light intensity on photocurrent (λ = 488 nm), (f) single cycle of photodetector illumination presenting the rise and fall times (λ = 488 nm, IL = 104 mW/cm2). An inset in figure (a) shows SEM image of the BiSI film. The words “ON”, “OFF” in figures (c,d) refer to the photodetector illumination and dark condition, respectively. The red line in figure (e) represents the best fitted dependence described by Eq. (4).

A typical single cycle of the normalized response of the BiSI photodetector is presented in Fig. 7f. The rise (tr) and fall (tf) times were calculated as the time intervals taken between 10 and 90% of the maximum photocurrent at the rising and recovery edges, respectively17,84. Figure S6 in the “Supplementary data” depicts the influence of the light intensity on rise and fall times averaged over multiple ON/OFF cycles of the photodetector illumination (Fig. 7d). An increase of the IL led to the slight and significant reduction of the tr and tf, accordingly. This effect was also reported in the case of the other photodetectors based on the BiSI film17, Ga2O3 film89, and ZnO nanowires90. The rise time tr = 5.9(16) s and fall time tr = 14(7) s were determined for the highest light intensity (IL = 127 mW/cm2). It was observed that the rise time is shorter than the decay duration, which strongly suggests that trap and defect states were involved. The Rose's model which proposes that traps and defect states are dispersed with variable concentration in the bandgap, is in good accord with the lowering of the rise and fall time with increasing light intensity. Since the semiconductor is not in a state of thermal equilibrium under illumination, extra electrons and holes are generated in the BiSI nanorods. As a result, two quasi-Fermi levels for electrons and holes are induced. The quasi-Fermi levels for electrons and holes move toward the conduction and valence bands, respectively, as light intensity rises, and an increasing number of traps become recombination sites. In result, the rising and fall times are drastically shortened91.

Different figures of merit are used commonly to characterize the sensing performance of the photodetectors, including responsivity (Rλ), external quantum efficiency (EQE), and detectivity (D). These parameters are described by the following equations92,93

where IPC is a photocurrent, Popt means an optical power density, IL denotes light intensity, S is the effective illumination area of the device, h = 6.63 × 10–34 J s is Planck’s constant, c = 3 × 108 m/s is light velocity, q = 1.6 × 10–19 C is the elementary charge, R·S is the resistance area product, kB = 1.38 × 10–23 J/K is Boltzmann constant, and T means temperature. The responsivity of 64(2) nA/W, external quantum efficiency of 1.63(5) × 10–5%, and detectivity of 1.27(5) × 108 Jones were determined for the Au/BiSI/Au photodetector under blue light illumination (λ = 488 nm, IL = 12.7 mW/cm2). It should be underlined that an increase of light intensity strongly reduces the responsivity, external quantum efficiency, and detectivity of the photodetector17,84. Therefore, an application of much smaller light intensity should result in a significant enhancement of Rλ, EQE, and D parameters. Such experiments will be performed in the future.

Table 3 presents the data reported in the literature for photodetectors constructed from various bismuth chalcohalide nanomaterials. The photodetector based on the BiSI nanorods showed shortened rise time than this determined for BiOCl-TiO2 heterojunction87. Moreover, it exhibited improved γ power coefficient in comparison to the BiSeI micro/nanowires84, which proved better sensitivity of the photocurrent response to the change of the light intensity.

The second type of examined photodetectors was flexible photo-chargeable BiSI capacitor (Fig. 8a). It consisted of the BiSI nanorods film and PVA-KOH gel electrolyte sandwiched in between the ITO coated PET substrates. The BiSI served as the light absorbing material. The porous structure of the film, composed of randomly oriented BiSI nanorods (Fig. 8b), facilitated higher ion diffusion from the electrolyte94,95. Figure 8c presents the current–voltage characteristics of the PET/ITO/BiSI/PVA-KOH/ITO/PET device registered in dark condition and under illumination with blue (λ = 488 nm) and red (λ = 632.8 nm) light. Figure 8d shows transient characteristic of the open-circuit photovoltage of the PET/ITO/BiSI/PVA-KOH/ITO/PET capacitor when no strain was applied to the device (α = 180°). The maximum value of the photovoltage attained 68 mV under monochromatic light illumination (λ = 488 nm, IL = 127 mW/cm2). After the bottom ITO electrode was illuminated (Fig. 8a), the charge carriers were generated inside the BiSI film and participated in the electrolyte ions arrangement32,96. The photogenerated electrons were injected into the ITO electrode. Since only one side of the device was illuminated, the nonuniform distribution of the charge carriers in the both electrodes was occurred leading to formation of the open-circuit photovoltage. The short-circuit current was increased and decreased when Ar laser was turned on and off, respectively (Fig. 8e).

(a) A scheme of the flexible photo-chargeable detector consisting of BiSI nanorods film, PVA-KOH gel electrolyte layer and ITO electrodes on PET, (b) SEM micrograph of BiSI nanorods film deposited on ITO electrode, (c) current–voltage characteristics of the PET/ITO/BiSI/PVA-KOH/ITO/PET photodetector measured in dark condition and under monochromatic light illumination (IL = 127 mW/cm2), transient characteristics of (d) open-circuit voltage, short-circuit photocurrent density registered at (e) the original state (α = 180°) and (f) bent state (α = 60°) of the PET/ITO/BiSI/PVA-KOH/ITO/PET photodetector (T = 293 K, RH = 50%, λ = 488 nm, IL = 127 mW/cm2).

The photoelectric response of the PET/ITO/BiSI/PVA-KOH/ITO/PET capacitor was examined for larger number of ON/OFF cycles with shorter time intervals (Fig. S7 in the “Supplementary data”). It proved an remarkable repeatability of the BiSI photodetector response. However, a small decrease of the amplitude of the short-circuit photocurrent was observed with increasing number of the ON/OFF cycle (Fig. 8e and Fig. S7b). This effect could result from degradation of PVA-KOH gel polymer electrolyte97. Time dependences of the photovoltage (Fig. 8d, Fig. S7a) and photocurrent (Fig. 8e, Fig. S7b) registered at the original state (α = 180°) were similar to these reported for other photo-chargeable capacitors32,96. The not only quantitatively but also qualitatively different transient response of the BiSI photodetector was measured when the device was bent at the angle of α = 60° (Fig. 8f). A strong influence of bending on a photocurrent response indicated a possibility of application of the device as a deformation sensor. The responsivity, external quantum efficiency, and detectivity of the PET/ITO/BiSI/PVA-KOH/ITO/PET capacitor were calculated using Eqs. (5–7). When capacitor was illuminated with blue light (λ = 488 nm, IL = 127 mW/cm2) and no strain was applied to the device, the figures of merit were following: Rλ = 8.7(8) nA/W, EQE = 2.2(2) × 10–6%, and D = 6.3(6) × 106 Jones.

The photoelectric performance of different photo-chargeable capacitors is presented in Table 4. The majority of these devices are stiff. It limits their potential applications. This drawback was eliminated in the flexible PET/ITO/BiSI/PVA-KOH/ITO/PET photodetector. Furthermore, the photovoltage generated in this device was higher than values of this parameter reported for SiO2/ITO/PANI/PVA-H2SO4/PANI-CNT/PET98 and SiO2/ITO/BiSI/PVA-KOH/BiSI/ITO/SiO232 capacitors.

The BiSI nanorods were fabricated via a facile wet chemical method. The high purity material was prepared at relatively low temperature (393 K) using low-cost and simple equipment. Moreover, the synthesis of the material was completed within 5 h. It is a great advantage in comparison to fabrication of BiSI using hydrothermal or solvothermal methods which require high temperature (typically 453 K) and long reaction time (over 15 h). The BiSI nanorods were characterized by applying many different experimental techniques, including HRTEM, SEM, EDS, XRD, and DRS. The orthorhombic BiSI was identified as the main phase of the synthesized material. The one-dimensional morphology of BiSI nanocrystals was revealed. The distribution of the BiSI nanorods dimensions followed well a log–normal function. The average diameter and length of the BiSI nanorods were equal to 126(3) nm and 1.9(1) µm, respectively. The detected chemical elements (bismuth, sulfur, and iodine) were homogeneously distributed in the BiSI nanorods. The direct energy band gap of 1.67(1) eV was determined and confirmed to be in agreement with literature data for BiSI.

The two types of devices were constructed from BiSI nanorods and tested as photodetectors. The first one was composed of BiSI film deposited on the stiff glass substrate and equipped with Au electrodes. The photocurrent response of the Au/BiSI/Au photodetector under monochromatic light illumination (488 nm) was measured at a constant bias voltage. The response of BiSI photodetector exhibited an excellent repeatability and stability. The influence of light intensity on the photocurrent was found to obey well-known power law. The relatively high power coefficient of 0.49(2) indicated a good sensitivity of the photocurrent response to the change of the light intensity. The second type of investigated photodetectors was flexible photo-chargeable capacitor, which contained the BiSI nanorods film and PVA-KOH gel electrolyte sandwiched between the ITO electrodes. The multilayer PET/ITO/BiSI/PVA-KOH/ITO/PET device was used to detect Ar laser radiation without a need to apply to photodetector an external power supply. The photoelectric response of the device was registered at its original state as well as it was bent at 600. When no strain was applied to the PET/ITO/BiSI/PVA-KOH/ITO/PET capacitor, it generated open-circuit photovoltage of 68 mV and short-circuit photocurrent density of 0.11 nA/cm2 under illumination with light intensity of 0.127 W/cm2. A strong effect of bending on a photocurrent response was observed. It is promising for future applications of the BiSI capacitor as a deformation sensor. The BiSI nanorods were demonstrated to possess a great potential for use in flexible photo-chargeable capacitors and self-powered photodetectors.

The datasets used and/or analyzed during the current study available from the corresponding author on reasonable request.

Ghorpade, U. V. et al. Emerging chalcohalide materials for energy applications. Chem. Rev. 123, 327 (2023).

CAS PubMed Google Scholar

Palazon, F. Metal chalcohalides: Next generation photovoltaic materials?. Sol. RRL 6, 2100829 (2022).

CAS Google Scholar

Sun, H. et al. A novel method to synthesize BiSI uniformly coated with RGO by chemical bonding and its application as a supercapacitor electrode material. J. Mater. Chem. A 9, 15452 (2021).

CAS Google Scholar

Sun, H., Yang, G., Chen, J., Kirk, C. & Robertson, N. Facile synthesis of BiSI and Bi13S18I2as stable electrode materials for supercapacitor applications. J. Mater. Chem. C 8, 13253 (2020).

CAS Google Scholar

Audzijonis, A., Žaltauskas, R., Sereika, R., Žigas, L. & Rėza, A. Electronic structure and optical properties of BiSI crystal. J. Phys. Chem. Solids 71, 884 (2010).

ADS CAS Google Scholar

Arivuoli, D., Gnanam, F. D. & Ramasamy, P. Growth of bismuth sulpho-iodide single crystals from vapour. J. Mater. Sci. 21, 2835 (1986).

ADS CAS Google Scholar

Kumar, R. R., Raman, G. & Gnanam, F. D. Growth of single crystals of bismuth sulpho iodide in gel. J. Mater. Sci. 24, 4531 (1989).

ADS CAS Google Scholar

Hahn, N. T., Self, J. L. & Mullins, C. B. BiSI micro-rod thin films: Efficient solar absorber electrodes?. J. Phys. Chem. Lett. 3, 1571 (2012).

CAS PubMed Google Scholar

Hahn, N. T., Rettie, A. J. E., Beal, S. K., Fullon, R. R. & Mullins, C. B. N-BiSI thin films: Selenium doping and solar cell behavior. J. Phys. Chem. C 116, 24878 (2012).

CAS Google Scholar

Frutos, M. M., Barthaburu, M. E. P., Fornaro, L. & Aguiar, I. Bismuth chalcohalide-based nanocomposite for application in ionising radiation detectors. Nanotechnology 31, 225710 (2020).

ADS CAS PubMed Google Scholar

Choi, Y. C. & Hwang, E. Controlled growth of BiSi nanorod-based films through a two-step solution process for solar cell applications. Nanomaterials 9, 1650 (2019).

CAS PubMed PubMed Central Google Scholar

Aguiar, I., Mombrú, M., Barthaburu, M. P., Pereira, H. B. & Fornaro, L. Influence of solvothermal synthesis conditions in BiSI nanostructures for application in ionizing radiation detectors. Mater. Res. Exp. 3, 25012 (2016).

Google Scholar

Xiong, J. et al. Solution growth of BiSI nanorod arrays on a tungsten substrate for solar cell application. ACS Sustain. Chem. Eng. 8, 13488 (2020).

CAS Google Scholar

Mombrú Frutos, M. et al. Understanding the crystal growth of bismuth chalcohalide nanorods through a self-sacrificing template process: A comprehensive study. Inorg. Chem. 61, 9231 (2022).

PubMed Google Scholar

Bargozideh, S., Tasviri, M. & Ghabraei, M. Effect of carbon nanotubes loading on the photocatalytic activity of BiSI/BiOI as a novel photocatalyst. Environ. Sci. Pollut. Res. 27, 36754 (2020).

CAS Google Scholar

Kumar, P. et al. Bismuth-based mixed-anion compounds for anode materials in rechargeable batteries. Chem. Commun. 58, 3354 (2022).

CAS Google Scholar

Farooq, S. et al. High gain solution-processed carbon-free BiSI chalcohalide thin film photodetectors. Adv. Funct. Mater. 31, 2104788 (2021).

CAS Google Scholar

Li, S. et al. Bismuth chalcogenide iodides Bi13S18I2 and BiSI: Solvothermal synthesis, photoelectric behavior, and photovoltaic performance. J. Mater. Chem. C 8, 3821 (2020).

CAS Google Scholar

Quarta, D. et al. Colloidal bismuth chalcohalide nanocrystals. Angew. Chem. Int. Ed. 61, e202201747 (2022).

CAS Google Scholar

Tiwari, D., Cardoso-Delgado, F., Alibhai, D., Mombrú, M. & Fermín, D. J. Photovoltaic performance of phase-pure orthorhombic BiSI thin-films. ACS Appl. Energy Mater. 2, 3878 (2019).

CAS Google Scholar

Ganose, A. M., Butler, K. T., Walsh, A. & Scanlon, D. O. Relativistic electronic structure and band alignment of BiSI and BiSeI: Candidate photovoltaic materials. J. Mater. Chem. A 4, 2060 (2016).

CAS Google Scholar

Su, X. et al. A facile and clean synthesis of pure bismuth sulfide iodide crystals. Russ. J. Inorg. Chem. 51, 1864 (2006).

Google Scholar

Sugathan, V. et al. Synthesis of bismuth sulphoiodide thin films from single precursor solution. Sol. Energy 230, 714 (2021).

ADS CAS Google Scholar

Ran, Z. et al. Bismuth and antimony-based oxyhalides and chalcohalides as potential optoelectronic materials. npj Comput. Mater. 4, 14 (2018).

ADS Google Scholar

Koc, H., Palaz, S., Mamedov, A. M. & Ozbay, E. Optical, electronic, and elastic properties of some A5B6C7 ferroelectrics (A = Sb, Bi; B = S, Se; C = I, Br, Cl): First principle calculation. Ferroelectrics 511, 22 (2017).

ADS CAS Google Scholar

Sasaki, Y. Photoconductivity of a ferroelectric photoconductor BiSI. Jpn. J. Appl. Phys. 4, 614 (1965).

ADS CAS Google Scholar

Nitsche, R., Roetschi, H. & Wild, P. New ferroelectric V. VI. VII compounds of the SbSI type. Appl. Phys. Lett. 4, 210 (1964).

ADS CAS Google Scholar

Govindaraj, P. & Venugopal, K. Intrinsic ultra-low lattice thermal conductivity in orthorhombic BiSI: An excellent thermoelectric material. J. Alloys Compd. 929, 167347 (2022).

CAS Google Scholar

Yoo, B. et al. Improved charge separation and photovoltaic performance of BiI3 Absorber layers by use of an in situ formed BiSI interlayer. ACS Appl. Energy Mater. 2, 7056 (2019).

CAS Google Scholar

Mistewicz, K. Photovoltaic Devices and Photodetectors BT—Low-Dimensional Chalcohalide Nanomaterials: Energy Conversion and Sensor-Based Technologies (Mistewicz, K. ed.). 95–125 (Springer, 2023).

Kunioku, H., Higashi, M. & Abe, R. Low-temperature synthesis of bismuth chalcohalides: Candidate photovoltaic materials with easily, continuously controllable band gap. Sci. Rep. 6, 32664 (2016).

ADS CAS PubMed PubMed Central Google Scholar

Pathak, A. K., Mohan, A. C. & Batabyal, S. K. Bismuth sulfoiodide (BiSI) for photo-chargeable charge storage device. Appl. Phys. A Mater. Sci. Process. 128, 298 (2022).

ADS CAS Google Scholar

Mistewicz, K. Devices for Energy Harvesting and Storage BT—Low-Dimensional Chalcohalide Nanomaterials: Energy Conversion and Sensor-Based Technologies (Mistewicz, K. Ed.). 61–93 (Springer, 2023).

Zhang, R. & Zeng, K. A novel flower-like dual Z-scheme BiSI/Bi2WO6/g-C3N4 photocatalyst has excellent photocatalytic activity for the degradation of organic pollutants under visible light. Diam. Relat. Mater. 115, 108343 (2021).

ADS CAS Google Scholar

Zhang, R., Zeng, K. & Zhang, T. Enhanced visible-light-driven photocatalytic activity of Bi2WO6-BiSI Z-scheme heterojunction photocatalysts for tetracycline degradation. Int. J. Environ. Anal. Chem. 1, 1–16 (2020).

Google Scholar

Zhou, C., Wang, R., Jiang, C., Chen, J. & Wang, G. Dynamically optimized multi-interface novel BiSI-promoted redox sites spatially separated n–p–n double heterojunctions BiSI/MoS2/CdS for hydrogen evolution. Ind. Eng. Chem. Res. 58, 7844 (2019).

CAS Google Scholar

Li, Z., Zhang, Q., Wu, L., Gu, W. & Liu, Y. Mechanochemical synthesis of BiSI and Bi19S27I3 semiconductor materials. Adv. Powder Technol. 30, 1985 (2019).

CAS Google Scholar

Murtaza, S. Z. M. & Vaqueiro, P. Rapid synthesis of chalcohalides by ball milling: Preparation and characterisation of BiSI and BiSeI. J. Solid State Chem. 291, 121625 (2020).

CAS Google Scholar

Lee, J., Min, B. K., Cho, I. & Sohn, Y. Synthesis and characterization of 1-D BiSI and 2-D BiOI nanostructures. Bull. Korean Chem. Soc. 34, 773 (2013).

CAS Google Scholar

Titirici, M. et al. The sustainable materials roadmap. J. Phys. Mater. 5, 32001 (2022).

Google Scholar

Demartin, F., Gramaccioli, C. M. & Campostrini, I. Demicheleite-(I), BiSI, a new mineral from La Fossa Crater, Vulcano, Aeolian Islands, Italy. Mineral. Mag. 74, 141 (2010).

CAS Google Scholar

Zankat, C. K. et al. Self-powered photodetector based on SnSe2/MoSe2 heterostructure. Mater. Today Energy 18, 100550 (2020).

CAS Google Scholar

Patel, R. P. et al. Highly flexible and foldable broad band WSe2/CuO heterostructure photodetector. Sens. Actuators A Phys. 356, 114339 (2023).

CAS Google Scholar

Reddy, K. S., Veeralingam, B. S., Borse, P. H. & Badhulika, S. High responsivity self-powered flexible broadband photodetector based on hybrid selenium-PEDOT:PSS junction. Org. Electron. 108, 106586 (2022).

Google Scholar

Chekke, T. et al. Au decorated ultrathin WS2-based single-electrode triboelectric nanogenerator for flexible self-powered photodetector. Sens. Actuators A Phys. 349, 114076 (2023).

CAS Google Scholar

Vuong, V.-H. et al. Flexible, stable, and self-powered photodetectors embedded with chemical vapor deposited lead-free bismuth mixed halide perovskite films. Chem. Eng. J. 458, 141473 (2023).

CAS Google Scholar

Patel, R. P. et al. Hand-print method for preparation of large area and binder free electrodes for photodetection and electrocatalytic hydrogen evolution. Sol. Energy 246, 343 (2022).

ADS CAS Google Scholar

Pataniya, P. et al. Paper-based flexible photodetector functionalized by WSe2 nanodots. ACS Appl. Nano Mater. 2, 2758 (2019).

CAS Google Scholar

Modi, K. H. et al. Alloy engineering in InxSn1-XS for enhanced photodetection application. Opt. Mater. (Amst.) 134, 113154 (2022).

CAS Google Scholar

Rietveld, H. M. Line profiles of neutron powder-diffraction peaks for structure refinement. Acta Crystallogr. 22, 151 (1967).

CAS Google Scholar

Rietveld, H. M. A profile refinement method for nuclear and magnetic structures. J. Appl. Crystallogr. 2, 65 (1969).

CAS Google Scholar

Toby, B. H. R factors in Rietveld analysis: How good is good enough?. Powder Diffr. 21, 67 (2006).

ADS CAS Google Scholar

Karolus, M. & Łągiewka, E. Crystallite size and lattice strain in nanocrystalline Ni–Mo alloys studied by Rietveld refinement. J. Alloys Compd. 367, 235 (2004).

CAS Google Scholar

Assi, A. A., Saleh, W. R. & Mohajerani, E. Effect of metals ( Au, Ag, and Ni) as cathode electrode on perovskite solar cells. IOP Conf. Ser. Earth Environ. Sci. 722, 12019 (2021).

Google Scholar

Chun, D. H. et al. Halide perovskite nanopillar photodetector. ACS Nano 12, 8564 (2018).

CAS PubMed Google Scholar

Luo, X. et al. Ultrasensitive flexible broadband photodetectors achieving PA scale dark current. npj Flex. Electron. 1, 6 (2017).

Google Scholar

Xu, Y. et al. Perovskite photodetectors based on p-i-n junction with epitaxial electron-blocking layers. Front. Chem. 8, 811 (2020).

ADS PubMed PubMed Central Google Scholar

Mikulics, M. et al. Ultrafast low-temperature-grown epitaxial GaAs photodetectors transferred on flexible plastic substrates. IEEE Photon.Technol. Lett. 17, 1725 (2005).

ADS CAS Google Scholar

Andersson, A. Mechanisms for log normal concentration distributions in the environment. Sci. Rep. 11, 16418 (2021).

ADS CAS PubMed PubMed Central Google Scholar

Borah, R. & Verbruggen, S. W. Effect of size distribution, skewness and roughness on the optical properties of colloidal plasmonic nanoparticles. Colloids Surf. A Physicochem. Eng. Asp. 640, 128521 (2022).

CAS Google Scholar

Selvaraj, J. et al. Phosphine-free, highly emissive, water-soluble Mn:ZnSe/ZnS core-shell nanorods: Synthesis, characterization, and in vitro bioimaging of HEK293 and HeLa cells. ACS Appl. Nano Mater. 1, 371 (2018).

CAS Google Scholar

Lu, C. et al. One-dimensional growth of zinc crystals on a liquid surface. Sci. Rep. 6, 19870 (2016).

ADS CAS PubMed PubMed Central Google Scholar

Patil, R. A., Devan, R. S., Lin, J.-H., Liou, Y. & Ma, Y.-R. An efficient methodology for measurement of the average electrical properties of single one-dimensional NiO nanorods. Sci. Rep. 3, 3070 (2013).

PubMed PubMed Central Google Scholar

Seshadri, G., Thaokar, R. & Mehra, A. Optimum size of nanorods for heating application. J. Magn. Magn. Mater. 362, 165 (2014).

ADS CAS Google Scholar

Mistewicz, K. Pyroelectric nanogenerator based on an SbSI-TiO2 nanocomposite. Sensors 22, 69 (2021).

ADS PubMed PubMed Central Google Scholar

Gadermaier, C. et al. Mo6S3I6 molecular wires: From one-dimensional electron fluids to a self-organised critical self-assembled network. J. Phys. Conf. Ser. 248, 12032 (2010).

Google Scholar

Kiss, L. B., Söderlund, J., Niklasson, G. A. & Granqvist, C. G. The real origin of lognormal size distributions of nanoparticles in vapor growth processes. Nanostruct. Mater. 12, 327 (1999).

Google Scholar

Wu, B.-K., Chern, M.-Y. & Lee, H.-Y. Size-controllable synthesis and bandgap modulation of single-layered RF-sputtered bismuth nanoparticles. Nanoscale Res. Lett. 9, 249 (2014).

ADS PubMed PubMed Central Google Scholar

Zhang, Y. C. et al. Application of electrochemical impedance spectroscopy in organic solar cells with vertically aligned TiO2 nanorod arrays as buffer layer. Key Eng. Mater. 512–515, 1598 (2012).

Google Scholar

Musa, I., Qamhieh, N. & Mahmoud, S. T. Synthesis and length dependent photoluminescence property of zinc oxide nanorods. Results Phys. 7, 3552 (2017).

ADS Google Scholar

Luo, H., Wei, M. & Wei, K. Synthesis of Nb2O5 nanorods by a soft chemical process. J. Nanomater. 2009, 758353 (2009).

Google Scholar

Groom, R., Jacobs, A., Cepeda, M., Drummey, R. & Latturner, S. E. Bi13S18I2: (Re)discovery of a subvalent bismuth compound featuring [Bi2]4+ dimers grown in sulfur/iodine flux mixtures. Chem. Mater. 29, 3314 (2017).

CAS Google Scholar

Groom, R. A., Jacobs, A., Cepeda, M., Drummey, R. & Latturner, S. E. Structural and optical properties of Sb-substituted BiSI grown from sulfur/iodine flux. Inorg. Chem. 56, 12362 (2017).

CAS PubMed Google Scholar

Patel, M., Chavda, A., Mukhopadhyay, I., Kim, J. & Ray, A. Nanostructured SnS with inherent anisotropic optical properties for high photoactivity. Nanoscale 8, 2293 (2016).

ADS CAS PubMed Google Scholar

Thomas, J. et al. Morphology dependent nonlinear optical and photocatalytic activity of anisotropic plasmonic silver. RSC Adv. 8, 41288 (2018).

ADS CAS PubMed PubMed Central Google Scholar

Abdullah, B. J. Size effect of band gap in semiconductor nanocrystals and nanostructures from density functional theory within HSE06. Mater. Sci. Semicond. Process. 137, 106214 (2022).

CAS Google Scholar

Delley, B. & Steigmeier, E. F. Size dependence of band gaps in silicon nanostructures. Appl. Phys. Lett. 67, 2370 (1995).

ADS CAS Google Scholar

Chen, Y.-H. & Ho, C.-H. Temperature dependence of direct and indirect band gaps of Bi13I2S18 hexagonal rod crystals. Mater. Chem. Phys. 206, 71 (2018).

ADS CAS Google Scholar

Modi, K. H., Pataniya, P. M., Patel, V. & Sumesh, C. K. Microwave assisted synthesis of SnS nanosheets for fabrication of large area SnS/Si heterojunction. Sol. Energy 221, 412 (2021).

ADS CAS Google Scholar

Patel, M., Pataniya, P. M. & Sumesh, C. K. ZnO-WS2 nano-heterojunction/ITO photodetector for detection of visible light. Mater. Sci. Semicond. Process. 148, 106778 (2022).

CAS Google Scholar

Chauhan, P. et al. Rhenium substitutional doping for enhanced photoresponse of N-SnSe2/p-Si heterojunction based tunable and high-performance visible-light photodetector. Appl. Surf. Sci. 536, 147739 (2021).

CAS Google Scholar

Zhang, J. et al. Toward smart flexible self-powered near-UV photodetector of amorphous Ga2O3 nanosheet. Mater. Today Phys. 31, 100997 (2023).

CAS Google Scholar

Fu, Y. et al. Enhanced property of flexible UV photodetectors based on electrospinning ZnO–SnO2 heterojunction nanofibers by the formation of Zn2SnO4. Ceram. Int. 49, 11402 (2023).

CAS Google Scholar

Hu, H. J. et al. Enhanced optoelectronic performance and photogating effect in quasi-one-dimensional BiSeI wires. Appl. Phys. Lett. 120, 201101 (2022).

ADS CAS Google Scholar

Zeng, W. et al. Synthesis of large-area atomically thin BiOI crystals with highly sensitive and controllable photodetection. Adv. Funct. Mater. 29, 1900129 (2019).

Google Scholar

Ouyang, W., Chen, J., He, J.-H. & Fang, X. Improved photoelectric performance of UV photodetector based on ZnO nanoparticle-decorated BiOCl nanosheet arrays onto PDMS substrate: The heterojunction and Ti3C2Tx MXene conduction layer. Adv. Electron. Mater. 6, 2000168 (2020).

CAS Google Scholar

Ouyang, W., Teng, F. & Fang, X. High performance BiOCl nanosheets/TiO2 nanotube arrays heterojunction UV photodetector: The influences of self-induced inner electric fields in the BiOCl nanosheets. Adv. Funct. Mater. 28, 1707178 (2018).

Google Scholar

Fang, H. & Hu, W. Photogating in low dimensional photodetectors. Adv. Sci. 4, 1700323 (2017).

Google Scholar

Wang, Y. et al. Improved response speed of β-Ga2O3 solar-blind photodetectors by optimizing illumination and bias. Mater. Des. 221, 110917 (2022).

CAS Google Scholar

Mallampati, B., Nair, S. V., Ruda, H. E. & Philipose, U. Role of surface in high photoconductive gain measured in ZnO nanowire-based photodetector. J. Nanoparticle Res. 17, 176 (2015).

ADS Google Scholar

Jiang, Y. et al. Photoresponse properties of CdSe single-nanoribbon photodetectors. Adv. Funct. Mater. 17, 1795 (2007).

CAS Google Scholar

Yadav, S. M. & Pandey, A. 2D-SnS2 nanoflakes based efficient ultraviolet photodetector. IEEE Trans. Nanotechnol. 19, 301 (2020).

ADS CAS Google Scholar

Yadav, S. M. & Pandey, A. Hybrid 2D–0D SnS2 nanoflakes/CTS QDs-based broadband (UV–visible–NIR) photodetector. IEEE Trans. Electron Dev. 67, 2008 (2020).

ADS CAS Google Scholar

De, P. et al. Role of porosity and diffusion coefficient in porous electrode used in supercapacitors—Correlating theoretical and experimental studies. Electrochem. Sci. Adv. 3, e2100159 (2023).

CAS Google Scholar

Zhu, M. et al. Capacitance enhancement in a semiconductor nanostructure-based supercapacitor by solar light and a self-powered supercapacitor-photodetector system. Adv. Funct. Mater. 26, 4481 (2016).

CAS Google Scholar

Boruah, B. D. & Misra, A. Voltage generation in optically sensitive supercapacitor for enhanced performance. ACS Appl. Energy Mater. 2, 278 (2019).

CAS Google Scholar

Fan, X. et al. Investigation of the environmental stability of poly(vinyl alcohol)–KOH polymer electrolytes for flexible zinc-air batteries. Front. Chem. 7, 678 (2019).

ADS CAS PubMed PubMed Central Google Scholar

Yin, Y., Feng, K., Liu, C. & Fan, S. A polymer supercapacitor capable of self-charging under light illumination. J. Phys. Chem. C 119, 8488 (2015).

CAS Google Scholar

Liu, P. et al. Controllable preparation of ultrathin 2D BiOBr crystals for high-performance ultraviolet photodetector. Sci. China Mater. 64, 189 (2021).

CAS Google Scholar

Prasad, M. D., Krishna, M. G. & Batabyal, S. K. Facet-engineered surfaces of two-dimensional layered BiOI and Au–BiOI substrates for tuning the surface-enhanced Raman scattering and visible light photodetector response. ACS Appl. Nano Mater. 2, 3906 (2019).

CAS Google Scholar

Qiao, H., Chen, X., Wang, B., Huang, Z. & Qi, X. Novel tin disulfide/graphene photoelectrochemical photodetector based on solid-state electrolytes and its performances. J. Mater. Sci. Mater. Electron. 30, 3208 (2019).

CAS Google Scholar

Chen, G., Zhou, Y., Zhang, G., Li, J. & Qi, X. Flexible, self-powered Bi2O2Se/graphene photoeletrochemical photodetector based on solid-state electrolytes. Ceram. Int. 47, 25255 (2021).

CAS Google Scholar

Download references

This paper was supported by Silesian University of Technology (Gliwice, Poland) through the Rector’s habilitation grant No. 14/010/RGH21/0008, Rector's grant No. 14/010/RGJ23/0012 in the area of scientific research and development, grant No. BK-221/RM4/2023 (11/040/BK_23/0029), and grant No. BK RM0: 11/990/BK_23/0084. SH and HJK would like to thank for the support by the Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Science and ICT of Korea (2021R1C1C1011588).

Institute of Physics - Center for Science and Education, Silesian University of Technology, Krasińskiego 8, 40-019, Katowice, Poland

Krystian Mistewicz & Tushar Kanti Das

Department of Industrial Informatics, Faculty of Materials Science, Joint Doctorate School, Silesian University of Technology, Krasinskiego 8, 40-019, Katowice, Poland

Bartłomiej Nowacki

Department of Industrial Informatics, Faculty of Materials Science, Silesian University of Technology, Krasinskiego 8, 40-019, Katowice, Poland

Albert Smalcerz

Department of Robotics and Mechatronics Engineering, Daegu Gyeongbuk Institute of Science and Technology, Daegu, 42988, Republic of Korea

Hoe Joon Kim & Sugato Hajra

Centre of Polymer and Carbon Materials, Polish Academy of Sciences, M. Curie-Skłodowskiej 34, 41-819, Zabrze, Poland

Marcin Godzierz & Olha Masiuchok

International Polish-Ukrainian Research Laboratory Formation and Characterization of Advanced Polymers and Polymer Composites (ADPOLCOM), Kyiv, Ukraine

Marcin Godzierz & Olha Masiuchok

E.O. Paton Electric Welding Institute, National Academy of Sciences of Ukraine, 11 Kazymyr Malevych Str, Kyiv, 03680, Ukraine

Olha Masiuchok

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

Authors declare that K.M. initiated and supervised the project, wrote the manuscript and supplementary data, prepared all figures and tables, performed SEM/EDS investigations, determined distribution of nanorods dimensions, carried out DRS measurements and calculated energy band gap, proposed the photodetectors configuration, registered and analyzed photodetector responses, and provided the funding. T.K.D. synthesized the BiSI nanorods and carried out SEM/EDS examinations. B.N. prepared and examined photodetectors. A.S. provided funding. H.J.K and S.H. performed TEM investigations and reviewed the manuscript. M.G. and O.M. performed XRD examination.

Correspondence to Krystian Mistewicz.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

Mistewicz, K., Das, T.K., Nowacki, B. et al. Bismuth sulfoiodide (BiSI) nanorods: synthesis, characterization, and photodetector application. Sci Rep 13, 8800 (2023). https://doi.org/10.1038/s41598-023-35899-7

Download citation

Received: 26 March 2023

Accepted: 25 May 2023

Published: 31 May 2023

DOI: https://doi.org/10.1038/s41598-023-35899-7

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.